How quickly do on-board loader scales pay for themselves?
Payback depends on how many tonnes you load, how far trucks are from target today and what an overload or reload costs you. Busy loading points often recover the cost within months through fuller trucks, fewer trips and fewer reloads. The most reliable answer comes from your own weighbridge data run through a simple calculation.
Every supplier will tell you loader scales pay for themselves. The useful question is how quickly they would on your machines, with your tonnes and your trucks.
This guide shows where the return comes from and walks through a simple way to estimate payback from your own figures. Background on the scales themselves is in our Measure pillar on payload weighing.
Key takeaways
- Underloading is the hidden cost, because every part load adds a trip.
- Overloads cost twice, in reloading time and legal exposure.
- Your weighbridge records already hold most of the numbers you need.
- Accuracy protects the return, so calibration belongs in the business case.
On-board weighing
Work out the payback on your fleet
Book a demo and our team will help you estimate the return from loader or excavator scales using your own loading data.
No obligation, just a real conversation about what you need.
Where the return comes from
- Fuller trucks: without a scale, operators tend to load under target to stay clear of overloads, and every shortfall means extra trips for the same tonnes.
- Fewer reloads: trucks that arrive at the weighbridge overweight must tip off and return, costing loader and truck time.
- Lower legal exposure: under the Chain of Responsibility, loaders and loading managers share responsibility for mass limits on road trucks.
- Less wear: overloaded trucks put extra strain on tyres, suspension and frames.
- Better data: each bucket record feeds production reporting and payload KPIs that find further gains.
A simple way to estimate payback
Pull three months of weighbridge tickets for one loading point and work through these steps.
- Average shortfall: compare each net weight with the truck’s target and average the gap on underweight loads.
- Extra trips: divide the total shortfall by a typical full load to see how many trips it added.
- Trip cost: multiply those trips by your cost per trip, including truck, driver and fuel.
- Reload cost: count overweight tickets and estimate the loader and truck time each one cost.
- Payback: divide the installed cost of the scale by the monthly saving.
| Illustration only | Example input |
| Trucks loaded per day | 80 |
| Average shortfall on underweight loads | 0.8 t |
| Share of loads underweight | 40 percent |
| Result | About 26 t a day left in the stockpile, or one to two extra trips |
Replace these example figures with your own. The point of the exercise is that the inputs come from your records, not from a brochure.
Comparing the cost with a weighbridge
For smaller operations, the alternative is often a weighbridge. Pricing reported in Quarry magazine placed weighbridges in the $80,000 to $120,000 range, with certified loader scales starting near $10,000. Which suits you is weighed up in our loader scale and weighbridge comparison.
What erodes the return
A scale that drifts gives away the savings it was bought to create. Build calibration into the case from the start. Our article on why loader scale accuracy drifts covers the warning signs, and Loadrite scale service and calibration sets out recommended intervals.
If you trade from the scale, include the cost of trade approval and verification. The overloading side of the case is illustrated in our NSW overloading case study, and our Chain of Responsibility guide explains the duties behind it.
Mostly fuller trucks and fewer reloads. Smaller gains come from reduced wear, lower overloading exposure and better production data.
Use your weighbridge tickets to measure average shortfall and overweight loads, convert them into extra trips and reloads, cost those, and divide the installed cost by the monthly saving.
No. Most of the return comes from loading accuracy. Trade approval and verification are only needed if you sell or charge by weight from the scale.
Build the case on your own numbers
Loader scales usually pay back through fuller trucks and fewer reloads, but the speed depends on your operation. Run your weighbridge data through the steps above, include calibration in the cost, and the business case will stand on facts you can defend.
Contact STA today
Written by
Anthony Laverty
Marketing Specialist, SmartTech Australia
Anthony works alongside SmartTech Australia’s field technicians and product specialists to explain the technology fitted to mining, quarrying, civil and waste fleets across Australia, from payload weighing and cab air filtration to proximity detection and site networks. Before joining STA he served six years in the Australian Army, including operational deployments.